Part 3 - Assembling the board

Let's begin with the case.

  1. Remove the components from the box if not already done.

  2. Use the supplied hex key to remove the plate screws.

    image-1600541595770.png

  3. Remove the plate from the case.

  4. If no screw was inserted into the PCB-conducting screw position out of the box, install this screw.

    image-1600541128616.png

     

  5. Flip the case over.
    Install the provided rubber feet into the insets.

    image-1600541499842.png

  6. If installing the solenoid:

    1. Prepare the PCB. Flip it upside-down, and locate the dedicated solenoid pads.

      image-1600541859788.png

    2. Solder the provided pin headers to the PCB.
      The headers should be positioned properly so that the pins sit flush and parallel against the PCB.
      One possible way to achieve this is to install the socket onto the header, solder the header into place with the socket-header assembly pressed against the PCB, then remove the socket from the header once the solder has cooled.

      image-1600542498675.png

    3. Tin the leads of the solenoid. Solder them to the provided pin sockets.

      image-1600542550271.png

  7. Install the stabilizers and spacebar pipe onto the plate. 

    Make sure the spacebar pipe matches the spacebar orientation you are using.
    Make sure the stabilizer inserts are oriented the correct way; the wire clip side should be facing away from the switch cutout.

    image-1600540594833.png
    Note: The stabilizers and spacebar pipe will not be rendered in the images below due to not having a 3D model on hand.

  8. Tune and test the switches if not already done.
    Snap the switches into the plate.

    image-1600540751746.png
    image-1600540778553.png

  9. Insert the PCB against the switches.

    image-1600540882717.png

  10. Solder the switches into place, making sure that the PCB is seated firmly against the switches.
    Excessive gaps between the plate and PCB may negatively affect acoustics.

  11. At this stage, it is highly recommended to connect the PCB to a computer to test the functionality of all keys.
    Repair any faulty joints and replace any dysfunctional switches.

  12. If installing the solenoid:

    1. Cut the provided 3M VHB adhesive sheet to cover this side of the solenoid.

      image-1600542763206.png

      Note that the wire exits on the side facing the viewer, and the plunger extends to the left upon powering.

    2. Peel off one side of the VHB and secure it to the solenoid. Peel off the other side but do not adhere to anything.

    3. Insert the solenoid into the cutout on the inside of the case, so the plunger extends to the left when powered and the wire exits on top. Insert carefully so the side with VHB does not come into contact with the case. 

    4. Align the solenoid within the cutout. Push the solenoid beam out to verify that it does indeed strike the surface when fully extended.

    5. Push the solenoid against the upper surface to fully adhere it into place.
      The solenoid should look like this once fully installed at idle, with the beam extending in the direction of the arrow when pushed out.

      image-1600547462340.png

  13. Place the provided O-rings atop the four plate mount points.

    image-1600541185160.png

  14. If installing the solenoid: 
    Connect the solenoid to the PCB.

  15. Insert the switch-plate-PCB-stabilizer assembly into the case, taking care so that the O-rings do not move from their positions.

    image-1600541318778.png

  16. Install the four plate screws, compressing the O-rings equally.

    image-1600541399365.png

  17. Install the keycaps.
    Test some keystrokes and verify that they are sent.

Congratulations! You have fully assembled the Lunar II.

THGlwWm.jpg

Now you are ready for the keymap editing and final remarks.